Electronic Xenon PSU500WHBX 500

Description

Electronic Power Supply for Xenon Lamps up to 500 W

Certified to DNVGL-CG-0339

Order code

HBX 500: Standard version
ZG 30Xe-S: 35Amps Ignitor with symmetrical ignition, no anode or cathode ground operating
ZG 30Xe-A: 35 Amps ignitor with asymmetric ignition anode or cathode ground operating
ZG 60Xe: 60 Amps ignitor with asymmetric ignition anode or cathode ground operating

Features

Power supply for xenon filled short arc lamps
Designed for xenon short arc lamps rated up to 500 W / 44 A
Output power customer selectable by controller voltage 0 – 5 V
Capable to drive lamp voltage ranges from 15 – 29 V
length x width x height (mm) 220 x 132 x 141, 2.660 kg
PSU boards inside IEC(UL) 60601 approved and HAL T tested
Input voltage range from 90V AC to 264V AC, power factor corrected line input
μP controlled, digital power management with high output stability over lamp lifetime
Output short circuit protected and “Arc to Ground” protected
Operation with cathode or anode to ground/PE possible
Galvanic separation of lamp output and line input, thermal shut off at 90°C
Shut off function for end of life and lamp fail parameter
Ballast cascadable for use for higher wattage Xenon lamps
Auxiliary regulated 24 V / 0.2 A output for subsystems, permanent available
Flexible design: new lamps and functions adaptable by software
Other lamps on request

Adapted for the following manufacturer

· Osram lamps · Ushio lamps · Luxtel lamps · Perkin Elmer lamps

Additional information

For Manufacturer	Osram, Superior Quartz, Ushio
Type (Ushio)	UXL 450, UXL 500
Type (Superior Quartz)	SX350, SX450, SX500X Series, SX550

ELECTRICAL DATA

All values are valid at 25 ± 5°C, unless otherwise noted

INPUT DATA
Nominal Operation	Symbol	Unit	Nominal	Tolerances	Remarks
Input voltage AC-Line	U	V AC	100 - 240	90 - 264	DC-Voltage
Input voltage DC-Line	U	V DC	DC-input is possible but not certified
System wattage	P_LI	W		600 - 1150	Depends on select
Input current	I_LI	A		5 - 14	Depends on select
Line frequency	Fin	Hz	50/60	47 - 63
Line power factor	PFC	1	1.0	0.93 - 1.0
Line inrush current limiting	A_peak		13	Limiting Element will be shorted by relais
Leakage current to PE	I_{Leak_SA}	μA	< 500 @ 230 V		Standalone
Other Operation Data
System wattage during ignition	P_lign	W	25	< 30
System wattage standbyoperation	P_LIStby	W	1.5	0.5 - 2.0

OUTPUT DATA
Ignition	Symbol	Unit	Nominal	Tolerances	Remarks
Ignition voltage	U_ign	kV_peak	± 8	± 3	Load capacity 15 - 20 pF
Ignition time	t_{ign on}	sec.	0.4	0.2 - 2
Run-up Operation
Run-up current @ 15 V Lamp-voltage	l_max l_max	A A	66	+ 10 % max.	Inside specified lamp-parameter (select by internal mode-switch)
In rush current	l_max	A	80		0 - 1 ms
Nominal Operation
Lamp voltage	U_La	V	10 - 29	± 5%	Depends on lamp select
Lamp wattage	P_La	W	1000	± 2%	Fixed factory set-up mode # 4 1000 W
Lamp current	I_La	A	Up to 66		Depend on set-up
End-Of Life-Cut off voltage	U _{La, max}	V	30	± 1V	After run-up completed
End-Of-Life-Cut off time	t _EOL-Off	s	< 0.2
RF-Ripple of output power	∆ _PLa,rip P _La	%	< 1 p-p		15,5 V - 30 V
50 Hz - 60 Hz ripple		%	< 1 p-p	< 4 p-p	13V 30V
Shift in output power with shift in input voltage	∆ P _La ∆ U _Ll	1		< 0.005	Within nominal values
Open circuit voltage	U _OCV	V	110	105 - 120

ACCREDITATION
GL in certification

GEOMETRY AND WEIGHT
	Symbol	Unit	Nominal	Tolerances	Remarks
Length x width x height	L x W x H	mm	220 x 132 x 141	± 1
Housing					Closed AL
Weight	W_B	kg	2.66

MESSTECHNIK

LIGHTING

PQUBE® 3

ENEIDA

HBX Series

Hot restrike Ignitor “ZG90HG”

ZG 180 XE

ZG 60 Hg

Electronic Ballasts

Igniters

Lamp Cross Reference

ROTEC Lighting Product