Electronic Xenon Ballast 2000W
HBX 2000
Modular Electronic Control Gear for DC short arc lamps up to 2000W
Modular Electronic Control Gear for DC short arc lamps up to 2000W
Features
-
- Designed for Xenon short arc lamps rated up to 2200W/ 102A
- Output power selectable by control Voltage 0-5V and/or presetting by Hex switch and adjustment Pot
- Capable to drive lamp voltage range up to 40V (switch off @ 41V)
- Ballast boards inside has IEC(UL) 60601 approval
- Input voltage range from 110V AC to 240V AC, (90V-262V) PF corrected
- μP controlled, digital power management with high output stability over lamp Lifetime
- Output short circuit protected and “Arc to Ground” protected
- Operation with Cathode or Anode to Ground/PE possible
- Galvanic separation of lamp output to line input, thermal shut off at 90°C
- Shut off function for end of life and lamp fail parameter
- PSUs cascadable for use for higher wattage Xenon lamps
- Auxiliary regulated 24V/ 0.15A output for Subsystems, permanently available
- line input, built-in EMI-filter: meets CE and FCC
ELECTRICAL DATA
All values are valid at 25 ± 5°C, unless otherwise noted.
| INPUT DATA | |||||
|---|---|---|---|---|---|
| Nominal Operation | Symbol | Unit | Nominal | Tolerances | Remarks |
| Input voltage AC-Line | U | V AC | 110-240 | 90-264 | - |
| Input voltage DC-Line | U | V DC | 150-320 DC-input is possible but not certified | ||
| System wattage | PLine | W | - | 1000-2400 | Depends on P select |
| Input current | ILI | A | - | 32 | Depends on P select |
| Line frequency | f in | Hz | 50/60 | 47-63 | - |
| Line power factor | PFC | 1 | 1.0 | 0.93 to 1.0 | - |
| Line inrush current limiting | Apeak | - | 50 | Limiting Element will be shorted by Relais | |
| Leakage Current to PE | ILeak_SA | µA | <1000@230 V | - | Standalone |
| OTHER OPERATION DATA | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| System wattage during ignition | PLine | W | 100 | <150 | - |
| System wattage standby-operation | PLIStby | W | 5 | <6 | - |
| LAMP OUTPUT DATA | |||||
|---|---|---|---|---|---|
| IGNITION | Symbol | Unit | Nominal | Tolerances | Remarks |
| Ignition voltage withZG120Xe | Uign | kVpeak | 36-46 | - | Depends on ignitor |
| Ignition time | tign out | sec. | 1 | 0.9-1.1 | - |
| automatic restart counter | sec. | 20 | - | Attempts (Ballast) | |
| Run-up Operation | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| Run-up Current = nominal | Imax | A | 102 | Inside specified lamp- parameter (select by preset switch) | |
| NOMINAL OPERATION | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| Lamp voltage | ULa | V | 22-40 | PSU output NOT Ignitor input | |
| Lamp wattage | PLa | W | 1100 to 2400 | Factory set-up 2000W | |
| Lamp current | ILa | A | up to 102 | Depend on set-up | |
| End-Of Life-Cut off voltage | ULa, max | V | 41 | +/- 1V | After run-up completed |
| End-Of-Life-Cut off time | tEOL-Off | S | <0.2 | ||
| RF-Ripple of output power | ∆PLarip/ PLa | % | <1 | ||
| 50Hz-60Hz Ripple | % | <1 p-p | <4 p-p | ||
| Shift in output power with shift | ∆PLa/ | 1 | <0.005 | with nominal values | |
| in input voltage | ∆ULI | ||||
| Open circuit voltage for ignition | U | V | 110 | 105-160 | |
