Electronic Xenon Ballast 1600W
HBX 1600
Modular Electronic Control Gear for DC short arc lamps up to 1600W
Modular Electronic Control Gear for DC short arc lamps up to 1600W
Features
-
- Designed for Xenon short arc lamps rated up to 1800W/ 110A
- Output power customer selectable by control Voltage 0-5V and/or presetting by Hex switch and adjustment Pot
- Capable to drive lamp voltage range up to 36V (switch off @ 40V)
- Ballast boards inside IEC(UL) 60601 approved and HALT tested
- Input voltage range from 160V AC to 264V AC, power factor corrected
- µP controlled, digital power management with high output stability over lamp lifetime
- Output short circuit and “Arc to Ground” protected
- Operation with Cathode or Anode to Ground/PE possible
- Galvanic separation of lamp output to line input, thermal shut off at 90°C
- Shut off function for end of life and lamp fail parameter
- Auxiliary regulated 24V/ 0.15A output for Subsystems, permanent available
- Line input, built-in EMI-filter: meets CE and FCC
ELECTRICAL DATA
All values are valid at 25 ± 5°C, unless otherwise noted.
| INPUT DATA | |||||
|---|---|---|---|---|---|
| Nominal Operation | Symbol | Unit | Nominal | Tolerances | Remarks |
| Input voltage AC-Line | U | V AC | 180-240 | 160-264 | - |
| Input voltage DC-Line | U | V DC | 180-320 DC-input is possible but not certified | ||
| System wattage | PLine | W | - | 1000-2000 | Depends on P select |
| Input current | ILI | A | - | 12 | Depends on P select |
| Line frequency | f in | Hz | 50/60 | 47-63 | - |
| Line power factor | PFC | 1 | 1.0 | 0.93 to 1.0 | - |
| Line inrush current limiting | Apeak | - | 30 | Limiting Element will be shorted by Relais | |
| Leakage Current to PE | ILeak_SA | µA | <1000@230 V | - | Standalone |
| OTHER OPERATION DATA | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| System wattage during ignition | PLine | W | 25 | <30 | - |
| System wattage standby-operation | PLIStby | W | 1.5 | 0.5-2.0 | - |
| LAMP OUTPUT DATA | |||||
|---|---|---|---|---|---|
| IGNITION | Symbol | Unit | Nominal | Tolerances | Remarks |
| Ignition voltage withZG120Xe | Uign | kVpeak | 30-35 | - | Depends on ignitor |
| Ignition time | tign | sec. | 1 | 0.9-1.1 | - |
| automatic restart counter | sec. | 5 | Attempts (Ballast) | ||
| Run-up Operation | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| Run-up Current = nominal | Imax | A | 110 | Inside specified lamp- parameter (select by preset switch) | |
| Current | Imax | A | Inside specified lamp- parameter (select by preset switch) | ||
| NOMINAL OPERATION | |||||
|---|---|---|---|---|---|
| Symbol | Unit | Nominal | Tolerances | Remarks | |
| Lamp voltage | ULa | V | 10-36 | Depends on lamp select | |
| Lamp wattage | PLa | W | 900 to 1800 | Factory set-up 1600W | |
| Lamp current | ILine | A | up to 110 | Depend on set-up | |
| End-Of Life-Cut off voltage | ULa, max | V | 40 | +/- 1V | After run-up completed |
| End-Of-Life-Cut off time | tEOL-Off | S | <0.2 | 0 | |
| RF-Ripple of output power | ∆PLarip/ | % | <1 p-p | <4 p-p | |
| 50Hz-60Hz Ripple | % | <1 p-p | <4 p-p | ||
| Shift in output power with shift | ∆PLa/ | 1 | <0.005 | with nominal values | |
| in input voltage | ∆ULI | ||||
| Open circuit voltage for ignition | U | V | 110 | 105-120 | |
